Details
It doesn't get much easier than this. 100% full control over your Genesis Coupe 2.0T at your fingertips, with a VERY SOLID base map!
Features:
• Direct plug and play replacement of the OEM ECU, No re-wiring necessary
• Uses the vehicles standard sensors & engine hardware
• Electronic Throttle Control - (Drive By Wire) with Cruise Control
• Retains instrument panel functionality via CAN communications
• Windows 2000, XP, Vista, Windows 7 compatible software
• Real time programming, instant hesitation free adjustment while engine is running
• Fully user definable 32 x 32 mapping with over 30 correction tables available
• Tuning via Volumetric Efficiency (VE) or Injection time
• OBDII Diagnostic Trouble Code Storing & Check Engine Light Control – Generic OBDII protocol Only
• Wideband “auto tuning” using user definable target AFR table
• USB and CAN Communication Port
Factory Outputs:
• 4 x Fuel Injector outputs (Peak & Hold)
• 4 x Ignition outputs (15A Internal)
• Electronic Throttle Control (DBW)
• AC Clutch Relay
• Check Engine Light
• Fuel Pump
• Thermo Fan Outputs Cruise Control
• Factory Inputs: MAP sensors Throttle Position Sensor Knock Detection Sensor
• Narrow Band Oxygen sensor
• Coolant Temperature sensor
• Vehicle Speed Sensor
• Air Temperature sensor Power Steering Switch Oil Temperature Sensor
• Brake Switch Clutch Switch
• Expansion I/O: 4 x Analogue Voltage Inputs, 1 x Digital Input, 4 x Digital Outputs
• Configurable for: Aux Rev Limiter Exhaust Gas Temperature Sensors Air Temperature Switch
• Flat Shift Fuel Temperature Sensors
• Aux Fuel Pump
• NOS Enable Oil Temperature Sensors
• Boost Control
• Fuel Pressure Sensor
• Diff Temperature Sensor
• Battery Light
• External Map Sensor (Up to 5 Bar)
• Gearbox Temperature Sensor
• Generic Duty Output
• Oil Pressure Sensor
• Generic Temperature Sensors
• Nitrous Activation Switch
• Wideband O2 Sensors
• Discrete ON/OFF Switches
• Flex Fuel Sensor
Plus much more …
Expansions I/O:
Up to 36 more I/O channels are available using the optional Haltech I/O 12 and TCA 2/4 CAN Devices -
Functions:
• Closed Loop O2 Control
• Knock Control
• Long Term Fuel Trim
• Rev Limiter
• Closed/Open Loop Boost Control
• Gear Setup
• Nitrous Activation Output
• Over Boost protection
• Fuel Composition (E85/Flex Fuel)
• Speed Limiter
• Antilag Launch
• Decel Cut
Correction Tables:
• Fuel Ignition Boost
• Air Temperature Correction
• Air Temp Duty Correction
• Coolant Temperature Correction
• Map Correction
• Zero Throttle Gear Correction
• Cylinder Trim TPS Correction
• Generic Correction
• Gear Correction
Miscellaneous: Data Logging:
• 448Kb of onboard data logging, Storage for approx 40 minutes at 10 logs per seconds, 6 channels of data
• Max 20 channels logging capability
• Tune can be password protected in software
• Rugged anodized aluminum casing
Factory Functions:
• Not Supported: Immobilizer Traction Control
More Information
| Part Number | HT-055045 |
|---|---|
| Part Includes |
|
| Brand | Haltech |
| Type of Part | Engine Management |
| Engine Fitment | 2.0L (MT Only) |
| Length | 5.0 |
| Width | 18.0 |
| Height | 10.0 |
| Weight | 10.000000 |
Reviews
Write Your Own Review
Fitment
Details
It doesn't get much easier than this. 100% full control over your Genesis Coupe 2.0T at your fingertips, with a VERY SOLID base map!
Features:
• Direct plug and play replacement of the OEM ECU, No re-wiring necessary
• Uses the vehicles standard sensors & engine hardware
• Electronic Throttle Control - (Drive By Wire) with Cruise Control
• Retains instrument panel functionality via CAN communications
• Windows 2000, XP, Vista, Windows 7 compatible software
• Real time programming, instant hesitation free adjustment while engine is running
• Fully user definable 32 x 32 mapping with over 30 correction tables available
• Tuning via Volumetric Efficiency (VE) or Injection time
• OBDII Diagnostic Trouble Code Storing & Check Engine Light Control – Generic OBDII protocol Only
• Wideband “auto tuning” using user definable target AFR table
• USB and CAN Communication Port
Factory Outputs:
• 4 x Fuel Injector outputs (Peak & Hold)
• 4 x Ignition outputs (15A Internal)
• Electronic Throttle Control (DBW)
• AC Clutch Relay
• Check Engine Light
• Fuel Pump
• Thermo Fan Outputs Cruise Control
• Factory Inputs: MAP sensors Throttle Position Sensor Knock Detection Sensor
• Narrow Band Oxygen sensor
• Coolant Temperature sensor
• Vehicle Speed Sensor
• Air Temperature sensor Power Steering Switch Oil Temperature Sensor
• Brake Switch Clutch Switch
• Expansion I/O: 4 x Analogue Voltage Inputs, 1 x Digital Input, 4 x Digital Outputs
• Configurable for: Aux Rev Limiter Exhaust Gas Temperature Sensors Air Temperature Switch
• Flat Shift Fuel Temperature Sensors
• Aux Fuel Pump
• NOS Enable Oil Temperature Sensors
• Boost Control
• Fuel Pressure Sensor
• Diff Temperature Sensor
• Battery Light
• External Map Sensor (Up to 5 Bar)
• Gearbox Temperature Sensor
• Generic Duty Output
• Oil Pressure Sensor
• Generic Temperature Sensors
• Nitrous Activation Switch
• Wideband O2 Sensors
• Discrete ON/OFF Switches
• Flex Fuel Sensor
Plus much more …
Expansions I/O:
Up to 36 more I/O channels are available using the optional Haltech I/O 12 and TCA 2/4 CAN Devices -
Functions:
• Closed Loop O2 Control
• Knock Control
• Long Term Fuel Trim
• Rev Limiter
• Closed/Open Loop Boost Control
• Gear Setup
• Nitrous Activation Output
• Over Boost protection
• Fuel Composition (E85/Flex Fuel)
• Speed Limiter
• Antilag Launch
• Decel Cut
Correction Tables:
• Fuel Ignition Boost
• Air Temperature Correction
• Air Temp Duty Correction
• Coolant Temperature Correction
• Map Correction
• Zero Throttle Gear Correction
• Cylinder Trim TPS Correction
• Generic Correction
• Gear Correction
Miscellaneous: Data Logging:
• 448Kb of onboard data logging, Storage for approx 40 minutes at 10 logs per seconds, 6 channels of data
• Max 20 channels logging capability
• Tune can be password protected in software
• Rugged anodized aluminum casing
Factory Functions:
• Not Supported: Immobilizer Traction Control
More Information
Reviews
Fitment
It doesn't get much easier than this. 100% full control over your Genesis Coupe 2.0T at your fingertips, with a VERY SOLID base map!
Features:
• Direct plug and play replacement of the OEM ECU, No re-wiring necessary
• Uses the vehicles standard sensors & engine hardware
• Electronic Throttle Control - (Drive By Wire) with Cruise Control
• Retains instrument panel functionality via CAN communications
• Windows 2000, XP, Vista, Windows 7 compatible software
• Real time programming, instant hesitation free adjustment while engine is running
• Fully user definable 32 x 32 mapping with over 30 correction tables available
• Tuning via Volumetric Efficiency (VE) or Injection time
• OBDII Diagnostic Trouble Code Storing & Check Engine Light Control – Generic OBDII protocol Only
• Wideband “auto tuning” using user definable target AFR table
• USB and CAN Communication Port
Factory Outputs:
• 4 x Fuel Injector outputs (Peak & Hold)
• 4 x Ignition outputs (15A Internal)
• Electronic Throttle Control (DBW)
• AC Clutch Relay
• Check Engine Light
• Fuel Pump
• Thermo Fan Outputs Cruise Control
• Factory Inputs: MAP sensors Throttle Position Sensor Knock Detection Sensor
• Narrow Band Oxygen sensor
• Coolant Temperature sensor
• Vehicle Speed Sensor
• Air Temperature sensor Power Steering Switch Oil Temperature Sensor
• Brake Switch Clutch Switch
• Expansion I/O: 4 x Analogue Voltage Inputs, 1 x Digital Input, 4 x Digital Outputs
• Configurable for: Aux Rev Limiter Exhaust Gas Temperature Sensors Air Temperature Switch
• Flat Shift Fuel Temperature Sensors
• Aux Fuel Pump
• NOS Enable Oil Temperature Sensors
• Boost Control
• Fuel Pressure Sensor
• Diff Temperature Sensor
• Battery Light
• External Map Sensor (Up to 5 Bar)
• Gearbox Temperature Sensor
• Generic Duty Output
• Oil Pressure Sensor
• Generic Temperature Sensors
• Nitrous Activation Switch
• Wideband O2 Sensors
• Discrete ON/OFF Switches
• Flex Fuel Sensor
Plus much more …
Expansions I/O:
Up to 36 more I/O channels are available using the optional Haltech I/O 12 and TCA 2/4 CAN Devices -
Functions:
• Closed Loop O2 Control
• Knock Control
• Long Term Fuel Trim
• Rev Limiter
• Closed/Open Loop Boost Control
• Gear Setup
• Nitrous Activation Output
• Over Boost protection
• Fuel Composition (E85/Flex Fuel)
• Speed Limiter
• Antilag Launch
• Decel Cut
Correction Tables:
• Fuel Ignition Boost
• Air Temperature Correction
• Air Temp Duty Correction
• Coolant Temperature Correction
• Map Correction
• Zero Throttle Gear Correction
• Cylinder Trim TPS Correction
• Generic Correction
• Gear Correction
Miscellaneous: Data Logging:
• 448Kb of onboard data logging, Storage for approx 40 minutes at 10 logs per seconds, 6 channels of data
• Max 20 channels logging capability
• Tune can be password protected in software
• Rugged anodized aluminum casing
Factory Functions:
• Not Supported: Immobilizer Traction Control
